Understanding Essential Plumbing Skills is Essential for Installing a Bathtub
Understanding Essential Plumbing Skills is Essential for Installing a Bathtub
Blog Article
We've stumbled on this great article pertaining to How to Install a Bathtub Yourself down the page on the internet and reckoned it made sense to write about it with you on my blog.
Installing a tub isn't specifically brain surgery, but it does require solid plumbing, carpentry, as well as often, tiling abilities. Changing an old bathtub with a new one is likewise a moderately difficult project. If the old bathtub is readily obtainable, the project can relocate easily; if you have to open up a wall to remove the old bathtub and place the new tub, the task is much harder. In either instance, the job is within a house handyman's abilities, although you will require a helper to leave the old bathtub and embeded in the new one. Ensure you have qualified yourself for the work and also fit trying it. As opposed to working with a professional to take control of a halfway-completed job, it is better to consider utilizing one before you start. Chances are you might need a professional plumber to make tube links.
This article will assist you mount a brand-new bathtub in your washroom if you have actually currently purchased a brand-new tub and also don't require to alter the setup of your previous water system pipes.
Your tools and also material checklist should make up the following:
Preparing for the Setup
First of all, the supporting framework supplied with the bathroom ought to be fitted (if needed) according to the supplier's directions. Next off, fit the taps or mixer to the tub. When suitable the tap block, it is necessary to make sure that if the faucet comes with a plastic washer, it is fitted between the bath and also the faucets. On a plastic bathroom, it is likewise practical to fit a supporting plate under the taps unit to prevent strain on the tub.
Fit the flexible tap adapters to the bottom of both taps using 2 nuts and also olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet through the hole in the bathroom. Make use of the nut supplied by the maker to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the adaptable overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bathroom. Ensure you utilize all of the supplied washing machines.
Attach the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom should now be ready to be suited its last position.
Removing Old Taps
If you need to change old faucets with brand-new ones as a part of your installation, after that the first thing you should do is disconnect the water system. After doing so, switch on the faucets to drain pipes any type of water continuing to be in the system. The procedure of eliminating the existing taps can be quite problematic due to the restricted accessibility that is frequently the case.
Use a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipelines to the taps. Have a towel ready for the continuing to be water that will come from the pipelines. Once the supply pipes have been gotten rid of, use the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the single faucets from turning throughout this process. Once the taps have actually been gotten rid of, the holes in the bath/basin will need to be cleaned of any type of old securing compound.
Before going on to fit the new taps, contrast the pipeline connections on the old taps to the brand-new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the new taps to fit.
Mounting the Bath tub
Using the two wooden boards under its feet, put the bathtub in the needed setting. The wooden boards are practical in equally spreading out the weight of the tub over the area of the boards rather than focusing all the weight onto 4 tiny factors.
The following goal is to guarantee that the bathtub is leveled all round. This can be attained by inspecting the spirit level and readjusting the feet on the tub until the level checks out level.
To mount taps, fit all-time low of the outermost versatile tap port to the appropriate supply pipe by making a compression sign up with; after that do the exact same for the other tap.
Turn on the water system as well as check all joints and also new pipework for leakages and tighten them if essential. Load the tub as well as also inspect the overflow electrical outlet and the typical electrical outlet for leaks.
Finally, repair the bathroom paneling as defined in the producer's user's manual. Tiling and also securing around the bathtub ought to wait till the bath tub has been used a minimum of once as this will settle it into its final placement.
Fitting New Taps
If the tails of the new taps are plastic, then you will need a plastic connector to prevent damage to the thread. One end of the connector fits on the plastic tail of the faucet and also the various other end gives a link to the existing supply pipes.
If you need to fit a monobloc, after that you will certainly need decreasing couplers, which connects the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next, place the tap in the mounting hole in the bath/basin making sure that the washers remain in location between the faucet and also the sink. Secure the tap in place with the supplier provided backnut. When the tap is safely in place, the supply pipelines can be connected to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with normal tap connectors. The former type needs to be connected to the faucet ends first, tightening just by hand. The supply pipelines can later on be connected to the other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Bathtub
In the area where the bathroom satisfies the floor tile, it is essential to secure the accompanies a silicone rubber caulking. This is essential as the installation can relocate sufficient to fracture a stiff seal, triggering the water to permeate the wall surface in between the bathroom and also the tiling, bring about issues with moisture as well as possible leakages to the ceiling below.
You can choose from a variety of coloured sealers to assimilate your fixtures and also fittings. They are marketed in tubes and also cartridges, and also can sealing voids up to a width of 3mm (1/8 inch). If you have a larger gap to fill, you can load it with twists of soaked paper or soft rope. Keep in mind to always fill the bath tub with water before securing, to permit the movement experienced when the bathtub remains in use. The sealant can fracture relatively very early if you do not take into consideration this activity prior to sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are additionally conveniently readily available on the marketplace. It is advisable to fit the tiles using waterproof or water-proof glue as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

I hope you enjoyed our section about How to Install a Bathtub. Thanks so much for taking the time to browse our blog. If you please take the time to distribute this entry if you enjoyed reading it. We love reading our article about Tools You Need to Install a New Bathtub .
Clog issue? Reach out! Report this page